#1 PUSH BUTTON (LOCATED ON LEFT SIDE OF MOTOR)
#2 PUSH BUTTON (LOCATED ON RIGHT SIDE OF MOTOR)

MOTOR SPEED: (Highest Speed)
1) Depress and hold #1 (left) push button (PB) until LED turns on.
2) Release PB. LED remains on.
3) Let the #1 PB remain idle for 10 seconds. The LED will turn off.
4) Motor is now preset to full speed.

MOTOR SPEED: (4 Selectable Slower Speeds)
1) Depress and hold #1PB until LED turns on.
2) Release #1 PB. LED remains on.
3) Prior to the LED turning off momentarily depress #1 PB. Each time PB is depressed (up to 4 times) the motor will run one step slower.
4) Let the #1 PB remain idle for 10 seconds. The LED will turn off.
5) Motor is now preset to the selected motor speed.

MOTOR RUN TIME: (1 to 30 seconds in 1 second steps)
1) Depress #2 PB until LED turns on, approximately 10 seconds.
2) Release #2 PB. Motor run time now preset to 1 second.
3) Prior to the LED turning off momentarily depress #2 PB. Each time PB is depressed (up to 29 times) the motor will run one second longer.
4) Let the #2 PB remain idle for 10 seconds. The LED will turn off.
5) Motor is now preset to the selected run time.

MOTOR ACTIVATION TEST:
1) Momentarily depress the #1 PB.
2) Following a 10 second delay the motor will run for the length of time and speed previously programmed. The LED remains on during the delay time and the motor run time.

TWO-TIME-A-DAY TIMER
Momentarily depress the #2 PB. LED will turn on for 2 seconds and then turn off.

AT THIS TIME THE TIMER WILL FEED AT DAYBREAK AND 1 HOUR BEFORE NIGHTFALL. MOTOR WILL RUN AT HIGH SPEED FOR 6 SEC.

AM FEED TIME PROGRAMMING
(0 to 11 AM feeding times)
                          AFTER                                           BEFORE
HOURS:  2.5  2.0  1.5  1.0  0.5  DAYBREAK  0.5  1.0  1.5  2.0  2.5
FEED         |      |    |     |     |              |          |     |     |     |      |
SLOT #:   1     2    3     4     5            6          7     8     9   10   11
Note: AM feedings may be set for 0 to 5 times after daybreak, at daybreak, and 0 to 5 times before daybreak.

ENTERING AM PROGRAMMING MODE:
1) Depress both the #1 and #2 PB for approximately 10 seconds.
2) Hold the buttons down until the LED blinks.
3) Release the buttons, LED remains on.
4) Momentarily depress the #1 PB, when released LED goes off.
5) At this time all previous AM programmed feeding times are cleared.

ADVANCING TO SELECTED FEED SLOTS:
1) The program is now located at feed slot number 1, that is, 2.5 hours after daybreak.
2) To advance to next feed slot (#2) momentarily depress the #1PB. The LED will light each time the push button is depressed. When released the LED will turn off.

ACTIVATING AM FEED TIMES:
1) To activate a selected feed slot momentarily depress the #2 push button. The LED will light indicating the unit will feed at the selected feed slot.

NOTE: Once you have advanced through 11 AM feed slots the programming mode is automatically ended. Thirty seconds of push button inactivity at any feed slot will also end the programming mode. Exiting the programming, either way, is indicated with a  flashing LED.

EXAMPLE: Prior to programming one must enter the AM programming mode, see above. To program the unit to feed at daybreak (6th feed slot) and one hour after daybreak (4th feed slot). Depress the # 1 PB 4 times and momentarily depress the # 2 PB, depress the #1 PB and additional 2 times and again momentarily depress the #2 PB. Allow unit to time out.

PM FEED TIME PROGRAMMING
(0 to 11 PM feeding times)
                       BEFORE                                              AFTER
HOURS:  2.5  2.0  1.5  1.0  0.5  DAYBREAK  0.5  1.0  1.5  2.0  2.5
FEED         |     |     |     |     |            |            |      |    |     |      |
SLOT #:   1     2    3     4    5           6            7     8    9    10   11
Note: PM feedings may be set for 0 to 5 times before nightfall, at nightfall, and 0 to 5 times after nightfall.

ENTERING PM PROGRAMMING MODE:
1) Depress both the #1 and #2 push buttons for approximately 10 seconds.
2) Hold the buttons down until the LED blinks.
3) Release the push buttons, LED remains on.
4) Momentarily depress the #2 PB, when released LED goes off.
5) At this time all previous PM programmed feeding times are cleared.

ADVANCING TO SELECTED FEED SLOTS:
1) The program is now located at feed slot number 1, that is, 2.5 hours before nightfall.
2) To advance to next feed slot (2) momentarily depress the #1 PB. The LED will light each time the push button is depressed. When released the LED will turn off.

ACTIVATING PM FEED TIMES:
1) To activate a selected feed slot momentarily depress the #2 push button. The LED will light indicating the unit will feed at the selected feed slot.

NOTE: Once you have advanced through 11 PM feed slots the programming mode is automatically ended. Thirty seconds of push button inactivity at any feed slot will also end the programming mode. Exiting the programming, either way, is indicated with a flashing LED.

EXAMPLE: Prior to programming one must enter the PM programming mode, see above. To program the unit to feed one hour before nightfall (4th feed slot) and at nightfall (6th feed slot) depress the # 1 PB 3 times and momentarily depress the # 2 PB, depress the #1 PB an additional two times and again momentarily depress the #2 PB. Allow unit to time out.